OliNo

Renewable Energy

LedNed spotlight MR16GU5.3 WW

Posted by Marcel van der Steen in Led lights, Light measurements Add comments

ledned_spotlight_mr16gu53_ww presents a led lightbulb that looks like a spotlight. It is a small lightbulb and has an MR16GU5.3 fitting. This article shows diverse lamp parameters, also gathered together in an Eulumdat file.

See this overview for a comparison with other light bulbs.

Summary measurement data

parameter meas. result remark
Color temperature 2978 K Warm white
Luminous intensity Iv 96 Cd
Beam angle 53 deg
Power P 2.8 W
Power Factor 0.66 For every 1 kWh net power consumed, there has been 1.1 kVAhr for reactive power.
Luminous flux 99 lm
Luminous efficacy 36 lm/W
CRI_Ra 82 Color Rendering Index.
Coordinates chromaticity diagram x=0.4310 and y=0.3900
Fitting GU5.3/MR16
D x H external dimensions 50 x 57 mm External dimensions of the lightbulb.
D luminous area 28 mm Dimensions of the luminous area (used in Eulumdat file). This is equal to the size of the frontglass.
General remarks The ambient temperature during the whole set of measurements was 24-28 deg C.

Warm up effect: during the warming up the illuminance and the consumed power reduce with 11 %.

Voltage dependency: the illuminance and power consumption are almost independent on the voltage (variation less than 5 %).

The Eulumdat file can be found via this link.

The color of the led is more yellow at a higher color temperature, and more orange at a lower color temperature, see also this photo.

Measurement report (PDF) olino-pdf

Eulumdat light diagram

An interesting graph is the light diagram, indicating the intensity in the C0-C180 and the C90-C270 plane. This light diagram below comes from the program Qlumedit, that extracts these diagrams from an Eulumdat file.

ledned_spotlight_mr16gu53_ww_light_diagram

The light diagram giving the radiation pattern.

It indicates the luminous intensity around the light bulb. This light bulb has symmetry over the z-axis, so the C0-C180 and C90-C270 planes show the same radiation pattern result.

The unit is Cd/1000lm, meaning the intensity in Cd assuming there would be 1000 lumen in the measured light bulb. This enables comparing different types of light bulbs.

Illuminance Ev at 1 m distance, or luminous intensity Iv

Herewith the plot of the averaged luminous intensity Iv as a function of the inclination angle with the light bulb.

ledned_spotlight_mr16gu53_ww_pp_avg

The radiation pattern of the light bulb.

This radiation pattern is not the same as the one given earlier. This is because of the (small) differences of beam angles in the different planes. In this graph the luminous intensity is given in Cd.

These averaged values are used (later) to compute the lumen output.

ledned_spotlight_mr16gu53_ww_ev_dep_kantelhoek

Intensity data of every measured turn angle at each inclination angle.

This plot shows per inclination angle the intensity measurement results for each turn angle at that inclination angle.  There is some more spread in intensity results at low inclination angles, when the lluminance is varying depending on the inclination angle. There is an abrupt decrease in illuminance at 45 deg.

When using the average values per inclination angle, the beam angle can be computed, being 53 degrees.

Luminous flux

With the averaged illuminance data at 1 m distance, taken from the graph showing the averaged radiation pattern, it is possible to compute the luminous flux.

The result of this computation for this light spot is a luminous flux of 99 lm.

Luminous efficacy

The luminous flux being 99 lm, and the power of the lightbulb being 2.8 W, yields a luminous efficacy of 36 lm/W.

A power factor of  0.66 means that for every 1 kWh net power consumed, a reactive component of 1.1 kVAr was needed.

Light bulb voltage 12.0 V
Light bulb current 342 mA
Power P 2.8 W
Apparent power S 4.2 VA
Power factor 0.66

Of this light bulb the voltage across ad the resulting current through it are measured and graphed.

ledned_spotlight_mr16gu53_ww_ii_u_i_waveforms

Voltage across and current through the lightbulb
The current has peaks; it seems that a capacitor is charged close to the tops of the voltage.
Also the power spectrum of the current is determined.

ledned_spotlight_mr16gu53_ww_ii_powerspectrumi_percent

The powerspectrum of the current through the light bulb.

There are higher harmonics apparent in the spectrum.

Color temperature and Spectral power distribution

ledned_spotlight_mr16gu53_ww_powerspectrum

The spectral power distribution of this light bulb.

The measured color temperature is about 3000 K which is warm white.

This color temperature is measured straight underneath the light bulb. Below a graph showing the color temperature for different inclination angles.

ledned_spotlight_mr16gu53_ww_cct_function_of_incl

Color temperature as a function of inclination angle.

The color temperature is given for inclination angles up to 50 degrees since at larger inclination angles there is too little illumination.

The value remains constant within 6 %.

Chromaticity diagram

ledned_spotlight_mr16gu53_ww_chromaticity

The chromaticity space and the position of the lamp’s color coordinates in it.

The light coming from this lamp is at a distance of the Planckian Locus (the black path in the graph).

Its coordinates are x=0.4310 and y=0.3900.

Color Rendering Index (CRI) or also Ra

Herewith the image showing the CRI as well as how well different colors are represented (rendered). The higher the number, the better the resemblance with the color when a black body radiator would have been used (the sun, or an incandescent lamp).

Each color has an index Rx, and the first 8 indexes (R1 .. R8) are averaged to compute the Ra which is equivalent to the CRI.

ledned_spotlight_mr16gu53_ww_cri

CRI of the light of this lightbulb.

The value of 82 is higher than 80 which is considered a minimum value for indoor usage.

Note: the chromaticity difference is 0.0049 indicates the distance to the Planckian Locus. Its value is lower than 0.0054, which means that the calculated CRI result is meaningful.

Voltage dependency

The dependency of a number of lamp parameters on the lamp voltage is determined. For this, the lamp voltage has been varied and its effect on the following lamp parameters measured: illuminance E_v [lx], color temperature CT or correlated color temperature CCT [K], the lamppower P [W] and the luminous efficacy [lm/W].

ledned_spotlight_mr16gu53_ww_voltagedependency

Lamp voltage dependencies of certain light bulb parameters, where the value at 12 V is taken as 100 %.

The consumed power and the illuminance vary slightly when the voltage varies between 10-15 V.

When the voltage at 12 V varies with + and – 0.25 V (comparable to +/- 5 V at 230 V), then the illuminance varies with less than + and – 0.25 %, which will not be visible when the voltage changes abruptly.

Warm up effects

After switch on of a cold lamp, the effect of heating up of the lamp is measured on illuminance E_v [lx], color temperature CT or correlated color temperature CCT [K], the lamppower P [W] and the luminous efficacy [lm/W].

ledned_spotlight_mr16gu53_ww_startupeffect

ledned_spotlight_mr16gu53_ww_startupeffect_end

Effect of warming up on different light bulb parameters. At top the 100 % level is put at begin, and at bottom at the end.

During warm up time of about 25 minutes, the light bulb gives about 11 % less light and consumes about 11 % less power.

Led color and color temperature

The leds with an orange hue emit warm white light, and the led with a yellow hue emit bright white light. This can be understood considering that warm white is made by using more phosphorescent with red/orange hue.

ledned_cw_and_ww_ledcolor

Left the led with orange hue (warm white) and right the led with yellow hue (bright white)

Leave a Reply

 

WP Theme & Icons by N.Design Studio
Privacy Policy Entries RSS Comments RSS Log in